Category Archives: Linear Drive

Motion Control – LCR16 Series Linear Rotary Actuator, 35mm stroke, 24VDC operation with 5 micron encoder

Motion Control – Linear Rotary Actuator

Motion Control Actuator


Vaughan, Ontario, Canada –The LCR16 from SMAC Moving Coil Actuators provides precision Z-theta motion within one small actuator, which is ideal for a pick, orient and place applications.  A wide variety of LCR16 linear rotary actuators are available with either direct drive or gearbox equipped rotary units.
motion control - electromate- robotics

The vacuum-built-in shaft through the rotary motor is available for some models to prevent dust build-up in the unit.

Motion Control – Servo Controller for Non-comutated Devices, e.g. voice coil motors, from Equipment Solutions!

Motion Control – Servo Controller for Non-comutated Devices!

motion control - Voice Coil Motor Controller

SCA601 Linear Servo Controller: High Performance analog PID Servo Control law; Digital control of PID tuning parameters; Analog Position Sensor input; High current linear amplifier; RS232 interface; 76 x 76 x 25


motion control - miniature components

 

 

Forestville, CA, – — The SCA601 Linear Servo Controller was specifically designed to control single phase, non-comutated devices like voice coil motors. It is a high performance single axis DC motor controller and amplifier system. It is comprised of a highly integrated single PC board level product with a cohesive interface and a compact heat sink.

Motion Control – Electric Cylinder from Moticont Has Zero Cogging and High Throughput!

Motion Control – Electric Cylinder Has Zero Cogging

 

motion control - electric cylindermotion control - moticont

 

Van Nuys, CA — Motion Control – Moticont has added another non-commutated linear actuator to its DDLM series of low cost actuators.

The 0.125 in. (3.2 mm) diameter shaft has an internal thread on each end, a total of length of 4.960 in (126.0 mm), and extends 1.585 in. (40.3 mm) past the mounting end of the actuator. The shaft extends thru the 3/8-32 UNF x 0.250 (6.4 mm) long threaded studs at each end of the housing which can be used for mounting the DDL-019-070-01 linear actuator. Long life plain linear bearings support the internal shaft at both end of the actuator.

Motion Control – Electromate Recognized with 2021 AHTD Foundation Award!

Motion Control – Electromate 2021 AHTD Foundation Award!

motion control - electromate components


motion control - electromateToronto, Ontario – June 18, 2021 – Electromate received a Foundation Award from the Association for High Technology Distribution (AHTD), recognizing the company’s 25 years of membership and support. This is the first year the Award has been given, honoring a small group of members out of approximately 300 automation solution providers and manufacturers.

The AHTD is dedicated to maximizing the productivity, growth, and enterprise opportunities of its high-tech automation solution provider and manufacturer members. These goals align with Electromate’s commitment to driving innovation, identifying emerging technologies and products, promoting the education of automation and motion control, and fostering its relationships with industry peers.

Motion Control – NEW! High Speed Integrated Bearing and Drive System Features +/- 5 Microm Repeatability!

Motion Control – High Speed Integrated Bearing and Drive System

motion control - high speed drive system

E. Longmeadow, MA –Motion Control – LM76 is the Exclusive North American Distributor of a new high speed integrated bearing and drive system featuring +/- 5 micron repeatability, and zero backlash! This new X-Axis BE125-10 Open Screw Drive System sets new standards for: Length of travel, speed, and precision for Cartesian Robots (robots that move in X,Y and Z axes according to Cartesian Coordinates also know as rectangular coordinates) and single axis linear stages!

motion control - linear bearings

The new X-Axis BE125-10 Open Screw Drive System is a compact linear stage measuring 125 mm (4.921 in.) wide x 86 mm (3.386 in.) high x 4391 mm (172.874 in.) long and can handle dynamic loads to 500 kg (1102 lbs). The standard stroke length is 4000 mm (157.480 in.) and custom stroke lengths to 10 m (32.8 ft) can be specified.

Direct Drive Linear Motor Has Integrated Encoder and Temperature Sensor for Increased Throughput!

Motion Control – Linear Actuator Gives Higher Throughput! 

motion control Voice coil motor with temperature sensor

Van Nuys, CA – Motion Control Products – The new patented SDLM-019-070-01-01 direct drive linear motor with integrated position and temperature sensors is the latest addition to the series of zero backlash, zero cogging, high acceleration, high speed, high resolution, long life motors from Moticont. Also known as an electric cylinder, this compact direct drive linear motor is just 0.75 in. (19.1 mm) in diameter and 2.75 in (69.9 mm) long.  Protected inside the motor housing, the linear optical quadrature encoder is directly connected to the shaft for the greatest possible accuracy.

motion control - moticont

Highest throughputs are achieved by the SDLM-019-070-01-01 linear motor when operating at peak efficiency monitoring the data from the internal temperature sensor.

The SDLM-019-070-01-01 direct drive linear motor has a stroke length of 0.500 in. (12.7 mm) and a continuous force rating of 7.3 oz. (2.0 N) and peak force of 23.0 oz (6.4 N).  This non-commutated direct drive servo motor features: Quiet long life, plain linear bearings, an integrated internal 1.25 micron resolution (0.000049 in.) quadrature optical encoder with differential outputs, and a non-rotating shaft.  Applications include: Manufacturing (assembly and inspection equipment), sorting and packaging, semiconductor handling, medical procedure tables and instruments, antenna positioning, dampers, door & valve actuators, agricultural equipment, shaking, and adjustable office furniture.

Direct coupling of the load or stage to the low inertia non-rotating shaft eliminates backlash and allows for high acceleration/deceleration.  Both ends of the actuator and shaft ends have threaded mounting holes for easy integration into new and existing applications. The SDLM-019-070-01-01 Direct Drive Linear Actuator is also available with a matching servo controller

About Moticont – About Moticont – Moticont is a manufacturer of motion control products. Their product line includes voice coil motors, three phase brushless motors and positioning stages and slides.

Moticont is committed to exceeding their customers’ quality expectations and industry standards throughout the design, manufacturing, service and technical support phases. Their modern manufacturing facility, highly controlled processes, committed staff, and extensive testing complement their product design strengths. This enables them to supply their clients with specialized small orders to high volume just-in-time deliveries.

They offer an extensive line of standard products ready to be shipped immediately from stock, and when standard products are not quite right for an application, highly trained design engineers are always available to develop custom motion control products to fit the specific needs or our customers.

For additional information contact Sales Team at Moticont, 6901 Woodley Ave, Van Nuys, CA 91406; Toll Free: +1 (888) 785-1804, Tel: +1 (818) 785-1800, moticont@moticont.comor visit the website at http://www.moticont.com


See this and other Motion Control Components from Moticont featured on:

http://MotionShop.com.com

http://AllMotionBlogger.com

http://Automation-Blogger.com

http://MotionControlBlogger.com

http://motioncontrolBuyersGuide.com

http://MotionControlWeb.com

http://MotionShop.net

http://Catalogs-MotionControl.com

motion control - moticint

 

Motion Control – Hollow Core Voice Coil Motor Has Low Inertia, High Precision available from Moticont!

Motion Control – Hollow Core Voice Coil Motor!

 

motion control - hollow core voice coil actuator

Van Nuys, CA — Motion Control – Moticont introduces an open aperture (hollow core) voice coil or moving coil linear motor from Moticont, the HVCM-051-025-013-01. Featuring an open aperture of 0.50 in. (12.7 mm) this low cost, clean room friendly non-commutated motor is available off-the-shelf. The light weight and low inertia moving coil of the linear actuator demonstrates: High acceleration/deceleration, high speed, zero cogging, and by connecting directly to the load, zero backlash.

motion control - moticont

The HVCM-051-025-013-01 Linear actuator has a hollow core that allows for optics, illumination, laser beams, or cables to pass through, additionally, it has a continuous force rating of 5.3 lbs (23.7 N) and a peak force of 16.9 lbs (74.8 N) at a 10% duty cycle. This compact voice coil actuator measuring just 2.000 in. (50.8 mm) dia. X 1.00 in. (25.4 mm) housing length with a 0.50 in. (12.7 mm) stroke is ideal for applications such as: Medical diagnostics and testing, laser beam steering, wafer handling, laser cutting and welding, dynamic vibration absorption, optical focusing, scanning, assembly, and positioning applications.

Two 10-32 UNF-2B x 0.25 in. (6.4 mm) deep threaded mounting holes on 1.000 in. (25.4 mm) centers in the housing and coil allows for flexible and easy integration into new and existing applications. When used in closed loop applications with an adequate optional position sensor, resolutions of less then 1 micron are achievable for millions of cycles. If a longer stroke, higher force, a smaller foot print, or customized mounting is required, consult Moticont’s team of engineers. All of Moticont’s voice coil linear actuators are available as complete plug-and-play systems, including: Position sensor, servo driver, power supply, and if required with a linear position sensor.

About Moticont – Moticont is a manufacturer of motion control products. Their product line includes voice coil motors, three phase brushless motors and positioning stages and slides.

Moticont is committed to exceeding their customers’ quality expectations and industry standards throughout the design, manufacturing, service and technical support phases. Their modern manufacturing facility, highly controlled processes, committed staff, and extensive testing complement their product design strengths. This enables them to supply their clients with specialized small orders to high volume just-in-time deliveries.

They offer an extensive line of standard products ready to be shipped immediately from stock, and when standard products are not quite right for an application, highly trained design engineers are always available to develop custom motion control products to fit the specific needs or our customers.

For additional information contact Sales Team at Moticont, 6901 Woodley Ave, Van Nuys, CA 91406; Toll Free: +1 (888) 785-1804, Tel: +1 (818) 785-1800, moticont@moticont.comor visit the website at http://www.moticont.com


See this and other Motion Control Components from Moticont featured on:

http://MotionShop.com.com

http://AllMotionBlogger.com

http://Automation-Blogger.com

http://MotionControlBlogger.com

http://motioncontrolBuyersGuide.com

http://MotionControlWeb.com

http://MotionShop.net

http://Catalogs-MotionControl.com

motion control - moticont

 

 

Motion Control – Linear Positioning Drives in NEMA 8 and NEMA 14 from Nanotec Electronic

Lead screw and high quality threaded nut for long service lifeNANOTEC-LogoNANOTEC-LS28-LS35

Medford, MA, Motion Control – Nanotec Electronic, U.S., Inc. has expanded the range of hybrid linear positioning drives by models in a NEMA 8 (20 mm flange size) and NEMA 14 (35 mm flange size). Linear positioning drives include a rotating screw mounted on the stepper motor. The linear movement is generated with the aid of an external nut. These motors are ideal for the design of compact linear axes as there is no need for the coupling and the bearing support point for the screw. The small linear positioning drives are used, for example, for scanning tasks in optical, mechanical or acoustic test equipment.

The hybrid linear positioning drives from Nanotec Electronic use special, maintenance-free thermo-plastic nuts. Despite its small size, the NEMA-8 model LS2018 delivers a force of 40 N and a step resolution of 0.005 mm. The NEMA-14 model LS3518 delivers a force of 140 N and a resolution of 0.01 mm. Standard screw lengths of 75 or 150 mm are available; customer-specific screw lengths can be optionally obtained. Both actuators can also be supplied with high-resolution (2000 incr./rev.) encoders.

LS2018NANOTEC-LS28

Type Force Feed Resolution
N mm/s µm/step
LS2818S0604-T6x1-75 60 20 5
LS2818S0604-T6x2-75 60 20 10
LS2818S0604-T5x5-75 30 100 25
LS2818L0604-T6x1-75 120 30 5
LS2818L0604-T6x2-75 120 30 10
LS2818L0604-T5x5-75 60 140 25
LS2818L1404-T6x2-75 140 40 10

 

LS3518NANOTEC-LS35

Type Force Feed Resolution
N mm/s µm/step
LS3518S1204-T6X1-75 240 50 5
LS3518S1204-T6X2-75 160 100 10
LS3518S1204-T5X5-75 85 250 25

 

NANOTEC-Logo

Nanotec Electronic US Inc.
38 Montvale Avenue, Suite 255 C15
Stoneham, MA 02180
USA

General Inquiries, Sales & Delivery Inquiries
Phone: 781 219 3343
Email: info@us.nanotec.com

Support
Email: support@us.nanotec.com

For other motion control products from NANOTEC go to http://us.nanotec.com

Motion Control – New, Three-Phase Linear Drive Does Not Sacrifice Acceleration for Resolution!

Motion Control Linear Drive Does Not Sacrifice Acceleration for Resolution!

San Luis Obispo, CA – Motion Control – The newest addition to the Trust Automation line of motion control Linear Drives is the TA330 linear three-phase servo drive. It is easily configured for three-phase DC brushless servo motors using Hall Effect sensors, three-phase AC brushless motors using external sinusoidal commutation, single-phase DC brushed servo motors in bridged mode, and brushless linear motors. Its flexibility allows motion system designers to easily integrate the latest developments in sinusoidal motor control and its benefits of zero cogging, no torque ripple, and smooth motion, into applications such as, “very high resolution” inspection systems, metrology instruments, and medical applications.

Additionally, the very low electrical noise of the TA330 motion control linear drive makes it ideal for integration in or near systems that have noise sensitive circuitry, such as transducers and sensors. Also the audible noise problems associated with PWM Drives are eliminated

This powerful 150 Volt, 900 W continuous (2700 W peak) linear drive can be configured to interface with any motion controller. Higher performance systems require a motion controller with the capability to generate the two +/- 10 VDC command signals needed for sinusoidal commutation. The third command signal is generated by the drive to maintain the highest level of precision. The TA330 Drive can be set up to operate in trapezoidal mode using Hall Effect sensors as feedback. The drive also features DTS control which allows the transconductance (torque control) to be changed on-the-fly. An additional benefit is that very high resolution control can be maintained without having to sacrifice power capability.

Additional features: The standard TA330 motion control drive requires a 24 Volt input to power logic and bias supplies. This standard configuration allows the TA330 to operate with extremely low electrical noise. For applications which are not as sensitive to electrical noise, an optional internal logic and bias supply can be provided which eliminates the need for the external 24 VDC logic supply.

Compact, measuring just 14.9 in. (37.9 mm) X 7.7 (19.5 mm) X 4.7 ( 11.9 mm), it can be used with high inertia mismatched stages and low inductance motors. Integral thermally controlled variable speed forced air cooling, a housing designed to protect against operator injury, easily made connections using ribbon connectors, SMB coaxial connectors, and pluggable-terminal connectors, demonstrate Trust Automation’s commitment to operator safety, quiet environment, and ease of integration.

Trust Automation’s motion control products include: Stand-alone motion and machine controllers, SynqNet I/O and SynqNet Drives, Brushed and Brushless Rotary Motors, Interconnect Products and Automation Engineering consulting covering Mechanical, Electrical, Software and System aspects of machine design. Since 1990 Trust Automation has provided Smart Solutions in Motion Control and Affordable Customization of motion related products.

For additional information contact Dave Rennie at Trust Automation, 143 Suburban Road, Bldg 100, San Luis Obispo, CA 93401; Tel: 805-544-0761, Fax: 805-544-4621, E-Mail: info@trustautomation.com or visit the Web site at http://www.trustautomation.com

Powered by WordPress and ThemeMag